Every slab leak job is different, but the core scope is consistent. Here is what is included in a standard slab leak repair Dallas TX job with our team, from the first detection visit through the final walkthrough. Anything beyond this scope, like full flooring replacement or cabinet rebuild, gets priced separately and approved before we start.
Hydrostatic pressure testing, thermal imaging, moisture mapping and boroscope inspection of wall cavities. You get a marked leak location and a written scope before any repair begins. Most detections take 45 to 90 minutes on site.
We cut out the failed copper or PVC section and either splice in new pipe or reroute the line through the attic or walls with PEX tubing. Reroutes avoid future slab work and are often the smarter long-term call on older Dallas homes.
Standing water comes out with a water extraction unit, then we set Dri-Eaz and Phoenix Restoration air movers and dehumidifiers. We log moisture readings daily and do not pull equipment until the structure reads dry.
Affected framing, subfloor and wall cavities get antimicrobial spray before anything is closed up. This stops mold growth from starting during the dry-out, which matters in Dallas humidity where mold can colonize a wet cavity in 24 to 48 hours.
We replace cut drywall, tape and float with joint compound, and match texture and paint. You get a finished wall, not a patched one. Most rebuild work takes two to three days after the structure is dry.
Photos of every affected area, daily moisture logs and a full Xactimate scope. We work directly with your adjuster so the covered portion of the claim moves without you playing middleman between trades.
Slab Leak Water Damage Dallas TX is the repair of a pressurized or drain line failure beneath a concrete foundation, plus the drying and restoration of everything that water touched. Copper and PVC lines under a Dallas slab sit in soil that shifts with our clay-heavy ground, and when a line cracks, water wicks up through the concrete into flooring, baseboards and wall cavities. You rarely see a puddle. You see a hot spot on the floor, a spike in the water bill, or a musty smell that will not quit.
Most of the calls we run in Dallas County start the same way: a homeowner notices the meter spinning with every fixture off, or hears water running under the floor at 2 a.m. Left alone, an under slab leak repair Dallas Texas job turns into a mold job, because a wet slab feeds mold growth inside wall cavities within 24 to 48 hours. That is why we treat slab leak water damage restoration Dallas as one continuous job: locate the leak, stop it, then dry the structure to IICRC WRT standards before anything goes back together.
You should know exactly what happens from the first phone call to the final moisture reading. Here is how a slab leak repair Dallas TX job runs with our team, start to finish.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Thermal Imaging Camera
Maps temperature differences in the slab and walls to locate hidden leaks without tearing up flooring. It is the fastest way to narrow a leak to a small area.
Moisture Meter
Confirms wet materials and tracks drying progress day by day. We log readings so you and your adjuster can see exactly when the structure reached baseline.
Hydrostatic Test Pump
Pressurizes the plumbing system to isolate and confirm a slab leak. It is the standard first step in any under slab leak repair Dallas Texas job.
Boroscope Camera
Inspects wall cavities, cabinet voids and under-floor spaces through a small access hole. It lets us see the damage without opening up a wall.
Dri-Eaz and Phoenix Restoration Equipment
Air movers and dehumidifiers that pull moisture out of framing, drywall and subfloor. These are the same units used on large commercial losses.
Water Extraction Unit
Removes standing water fast, often hundreds of gallons an hour. Getting water out quickly is the single biggest factor in preventing mold growth.
HEPA Vacuum and Ozone Generator
HEPA vacuuming captures fine mold spores and debris after remediation, and ozone treatment neutralizes musty odors at the source rather than masking them.
IICRC S500 Drying Standard
We follow the IICRC S500 standard for water damage restoration, which sets the drying goals, equipment ratios and moisture targets for each material type. It is the benchmark carriers recognize, and it is why our documentation holds up on claims.
IICRC WRT and ASD Protocols
Our technicians hold IICRC WRT and IICRC ASD certifications, which cover water restoration and applied structural drying. That training is what tells us when a wall cavity is dry and when it just looks dry.
Pressure Testing Before Close-Up
Every repaired or rerouted line gets pressure-tested before we close the wall or floor. If it does not hold, we do not sign off. It is a simple step that prevents callbacks.
Xactimate Scoping
We build the loss scope in Xactimate, the same estimating platform most insurance carriers use. That means line items match what the adjuster expects, which cuts back-and-forth and speeds up approval.
Antimicrobial and Encapsulant Application
After extraction and before rebuild, we apply antimicrobial spray to affected framing and encapsulant where needed. This stops mold growth during the dry-out and seals porous surfaces that held moisture.
01
What we do: We ran hydrostatic testing and thermal imaging, found a pinhole leak under the hall bath, and rerouted the line through the attic with PEX tubing. Drying ran four days, rebuild took two.
→ Water bill back to normal, no jackhammering in the living space, and the homeowner kept the original hardwood.
02
What we do: We dispatched a crew within two hours, shut down the hot water line, extracted standing water and set Dri-Eaz drying equipment that night. Repair and rebuild followed over the next week.
→ Tenant stayed in the unit, mold never started, and the landlord's claim was approved on the first submission.
03
What we do: Detection confirmed a slow cold-water leak under the slab. We repaired the line, removed wet drywall and insulation, treated framing with antimicrobial spray, and dried the cavity to baseline.
→ Odor gone, baseboard replaced, and mold testing came back clear at the final walkthrough.
04
What we do: We worked overnight, isolated the leak, repaired the line, extracted water and set drying equipment. Daily moisture logs went straight to the adjuster.
→ Store reopened in four days with no lost weekend revenue and a clean insurance file.
Dallas sits on expansive clay soil that swells when it rains and shrinks hard in summer drought. That constant movement is the number one cause of slab leaks here, especially in homes built between 1950 and 1985 with original copper pipe. Our summers push attic temperatures past 140 degrees Fahrenheit, which stresses PEX and copper alike, and our humidity means a wet wall cavity can grow mold in 24 to 48 hours. When we run slab leak restoration services Dallas TX jobs, we plan around those conditions: faster dry-out targets, more dehumidification, and antimicrobial treatment on every affected cavity. Winter matters too. North Texas freezes crack lines that were already stressed, and we get a wave of frozen pipe and slab leak calls every January. If you are looking for same-day slab leak detection Dallas TX, we keep crews on call through those cold snaps because that is when the calls come in.
Lakewood
Mostly 1940s to 1960s homes with original copper under the slab. Reroutes through the attic are common here because the floor plans make direct access tight.
University Area
A high concentration of rental duplexes and older multifamily buildings. Slab leaks here often affect two units, so we coordinate access and drying across both.
Preston Hollow
Larger homes with longer plumbing runs and more complex slab layouts. Detection takes longer, and reroutes often involve multiple lines.
Oak Cliff
Older housing stock with a mix of copper and galvanized lines. We see more repeat leaks here, so rerouting the whole run is often the better call.
Downtown and Uptown
High-rise and mid-rise buildings where slab leaks show up in parking garages and lower-level units. We work with building management on access and scheduling.
Expansive clay soil movement
Soil shifts crack copper lines and shear PVC joints. It is the leading cause of slab leaks in Dallas County, and it means repairs need flexibility built in, which is why we often recommend PEX reroutes.
Summer attic heat above 140 degrees Fahrenheit
Attic reroutes need insulation and proper support to survive the heat. We spec materials rated for the temperature swing and pressure-test after install.
Winter freeze events
Freezes crack stressed lines and drive a spike in emergency calls. We keep crews on standby through cold snaps so response times stay under two hours.
High humidity and slow drying
Dallas humidity slows evaporation, so we run more dehumidification capacity and extend drying timelines by a day on most jobs to hit baseline.
A slab leak is rarely just a plumbing problem. It cascades into flooring, walls, air quality and your insurance claim. Here are the issues we see most often and how we handle them.
Problem
A pinhole leak in a copper line can waste 10,000 to 30,000 gallons a month and drive your bill up hundreds of dollars before you see a drop of water.
Our Fix
We pressure-test the system, isolate the hot and cold lines, and pinpoint the leak with a thermal imaging camera. You get a confirmed location and a repair plan the same visit, usually within 90 minutes of arrival.
Problem
A hot water line leak under the slab heats the concrete and flooring above it. Left alone, that constant moisture warps hardwood, loosens tile and feeds mold in the subfloor.
Our Fix
We confirm the leak with a moisture meter and thermal scan, shut down the affected line, and repair or reroute it. Then we dry the slab and flooring to baseline so the damage does not spread.
Problem
That smell is usually mold growing in a wall cavity or under flooring fed by a slow slab leak. It gets worse over time and can affect air quality for everyone in the house.
Our Fix
We locate the moisture source, fix the leak, then test for mold. If growth is present, our TDLR-licensed team handles containment, removal and clearance so the air is clean again.
Problem
Soil movement and slab moisture cause tile to crack and baseboards to separate. It looks cosmetic, but it usually signals a leak that has been running for weeks.
Our Fix
We inspect the slab, run detection, and confirm whether a leak is present. If it is, we repair the line and dry the structure. If it is not, we tell you straight and point you to the right trade.
A slab leak is not a wait-and-see problem. Every hour the line runs, more water moves through your foundation and more of your flooring, drywall and insulation gets wet. Here is what you get when you call us instead of a general handyman.
Non-Invasive Leak Detection
We use a thermal imaging camera and a moisture meter to map the leak before anyone touches your floor. Most jobs need one small access point instead of a trench across the living room. That saves you thousands in concrete and flooring work, and it is why our slab leak detection Dallas customers usually get an answer within the first hour on site.
Same-Day Emergency Response
Our crews run 24/7 across Dallas County, so an emergency slab leak repair Dallas call at 2 a.m. gets a live dispatcher, not a voicemail. We shut down the affected line, stop the water, and set drying equipment the same visit. Most residential calls are stabilized within 90 minutes of arrival.
Full Dry-Out, Not Just a Patch
Fixing the pipe is half the job. We place Dri-Eaz and Phoenix Restoration air movers and dehumidifiers, track moisture readings daily, and document everything in Xactimate so your claim moves. A typical 400-square-foot affected area dries in three to five days at 90 to 100 degrees Fahrenheit with proper airflow.
9 Years Working Dallas Slabs
We have been at this since 2017, and a big share of our work is 1950s to 1980s Dallas homes with original copper under the slab. We know how those lines fail, where they fail, and how to repair them without tearing up your whole foundation. That experience is what keeps our repeat and referral rate high.
Google ★★★★★4.9
Found our slab leak in under an hour with a thermal camera. Rerouted the line instead of tearing up the floor and dried everything in four days. Honest pricing and they handled the insurance paperwork. Would call them again without hesitation.
Yelp ★★★★★5.0
Called at midnight on a Sunday and a real person answered. Crew was out in two hours, shut the water off and set drying equipment that night. Clean work, clear communication, and the final invoice matched the estimate exactly.
BBB ★★★★★4.8
We had a slab leak in a 1968 house and two other companies wanted to jackhammer the living room. These guys opened one small spot, fixed the line and saved us thousands. They also caught early mold in the wall and treated it before it spread.
Google ★★★★★4.9
Property manager here. Used them on three Dallas duplexes now. Documentation is clean, adjusters approve without pushback, and tenants stay in place during the work. That combination is hard to find.
Real experiences from customers who chose our Slab Leak Water Damage services.
“Our water bill doubled and we could hear water running at night. These guys found the leak under the hall bathroom in about an hour with a thermal camera. They rerouted the line through the attic instead of jackhammering the floor, dried everything out in four days, and handled the insurance paperwork. Nine days start to finish and you cannot tell anything happened.”
Marcus T.
Homeowner, Lakewood
“We had a slab leak in a 1968 house with original copper. Two other companies wanted to tear up the whole living room floor. This crew did slab leak detection with a moisture meter and a camera, opened one small spot, and repaired the line. Saved us thousands. They also caught mold starting in the wall cavity and treated it before it spread.”
Priya S.
Homeowner, 75230
“Called at 11 p.m. on a Sunday after a tenant reported hot spots on the floor. A real person answered, and a crew was out within two hours. They shut the line down, extracted water and set Dri-Eaz equipment that night. Documentation was clean enough that the adjuster approved the claim without a second visit. We use them on all our Dallas properties now.”
Danny R.
Property Manager, University Area
Real answers to the questions we hear most often from local homeowners and property managers.
When a slab leak spreads beyond the immediate area, full water damage restoration covers flooring, drywall, insulation and framing. We dry to IICRC S500 standards and document everything for your Dallas County insurance claim.
View Water Damage RestorationStanding water from a slab leak needs to come out fast. Our water extraction units pull hundreds of gallons an hour, and we set drying equipment the same visit to stop mold growth before it starts.
View Emergency Water RemovalA slab leak that runs for a week often means mold inside wall cavities. We hold Texas Mold Remediation Licensing through TDLR and handle containment, removal and clearance so your Dallas home is safe to live in.
View Mold RemediationNot sure whether that musty smell is mold? We test air and surface samples, identify the species, and tell you whether remediation is needed. It is a fast, inexpensive step after any slab leak in Dallas.
View Mold Testing & InspectionSome slab leak repairs involve opening walls near electrical runs. If a related fire or smoke event happens, we handle soot removal, odor treatment and full reconstruction under one roof.
View Fire & Smoke Damage RestorationA broken drain line under the slab can back sewage into your home. That is a Category 3 loss, and it needs antimicrobial treatment, removal of contaminated materials and full disinfection before rebuild.
View Sewage CleanupCall (469) 895-3421 any time, day or night. A live person answers, not a machine. We dispatch crews 24/7 across Dallas and the surrounding metro, and we average under 60 minutes to arrive. If you prefer email, reach us at info@dallashomemoldwaterfiredamage.com and we will respond the same day.
Phone
(469) 895-3421Address
3924 Sandshell Dr #5800, Fort Worth, TX 76137, Dallas, Texas
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available
